Plumbing 101: A Guide to Installing a Bathtub
Plumbing 101: A Guide to Installing a Bathtub
Blog Article
Listed here below you can get a lot of extremely good additional info when it comes to Tools You Need to Install a New Bathtub .
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably challenging job. If the old bathtub is easily easily accessible, the project can relocate speedily; if you have to open up a wall to remove the old tub and also place the brand-new tub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have qualified on your own for the work as well as fit attempting it. Rather than working with a specialist to take control of a halfway-completed task, it is far better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new tub in your restroom if you have currently gotten a new tub and also don't need to transform the plan of your previous water system pipes.
Your devices and product list should consist of the following:
Getting ready for the Installment
To start with, the sustaining frame supplied with the bath needs to be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the restricted accessibility that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before going on to fit the new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the required setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small points.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level as well as readjusting the feet on the tub till the level checks out degree.
To install faucets, fit the bottom of the furthest adaptable faucet adapter to the proper supply pipe by making a compression join; then do the very same for the various other faucet.
Switch on the supply of water and also inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill up the bath tub as well as also examine the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bath tub needs to wait till the tub has been utilized a minimum of when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in location in between the tap and the sink. Safeguard the faucet in place with the maker provided backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet ports. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a rigid seal, creating the water to pass through the wall in between the bathroom and the tiling, leading to issues with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and also cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to enable the movement experienced when the bathtub remains in usage. The sealant can break rather early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly offered on the marketplace. It is suggested to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that article on Installing A Bathtub from an acquaintance on another web blog. Those who enjoyed our blog posting plz be sure to share it. Kudos for your time. Visit again soon.
Leaks? Ring us! Report this page